Datamax O'Neil H-4310X Manuale dell'Operatore Pagina 122
- Pagina / 180
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
112 H-Class
Warning Messages Fault Messages (continued)
Displayed Message Description Possible Solution(s)
HEAD NEEDS CLEANING
The scheduled printhead
cleaning distance has
been reached.
Clean the printhead (see
Section 5.5.1).
To change the cleaning setting,
enter ADVANCED MENU /
MEDIA SETTINGS / PRINTHEAD
CLEANING MENU.
HOST CHANGES PENDING
The host has changed
the configuration of the
printer, but those
changes cannot take
effect until a “host reset
command” is issued.
To save these changes, send a
host reset command (in DPL);
or, to discard the changes,
perform a soft reset (see
Section 5.3.1).
INVALID ENTRY
The selection you are
attempting to make is
not valid or is not within
the acceptable
parameter range.
Enter a different setting or
parameter that falls within the
acceptable range.
LOW VOLTAGE
The printer has detected
a low operating voltage.
Possible low or fluctuating line
voltage levels have been
sensed. If the condition
persists, try moving the printer
to another outlet, or call for
service.
REWINDER FULL
The internal rewinder is
nearing capacity.
Unload the internal rewinder
soon.
RIBBON LOW
The ribbon supply is
almost empty.
Load a new roll of ribbon soon.
RTC RAM FAILURE
The printer was unable
to save settings in
permanent memory.
Possible faulty Main Logic Card.
Retry your save. If the
condition persists, call for
service.
TEMPERATURE PAUSE
A high printhead
temperature has been
detected.
Wait for the printhead to cool.
Afterward, printer operations
will automatically resume when
the printhead reaches an
acceptable temperature.
- Operator’s Manual 1
- Copyright Information 3
- Limitation of Liability 3
- H-4212 and H-6308 models: 4
- Waves Act 4
- Special Instructions 5
- Applicability 5
- Contents 7
- Overview 11
- Standard 12
- (available except as noted) 13
- 6 H-Class 16
- Getting Started 17
- 2.2 Installation 18
- Setting up the Printer 23
- 3.1.3 Rewinding Media 29
- 34
- 3.2 Media Sensor Adjustment 35
- 3.3 Ribbon Loading 36
- 30 H-Class 40
- Using the Control Panel 41
- 4.1.1 The Display 42
- 4.1.2 Keypad Functions 43
- 4.2 The System Menu 44
- 4.2.1 Media Settings 45
- Section 7 for label details 48
- 4.2.3 Printer Options 50
- 4.2.4 System Settings 61
- STANDARD 68
- 4.2.5 Communications 71
- ENABLED 74
- NETWORK REPORT 76
- 4.2.6 Diagnostics 79
- 4.2.7 MCL Options 82
- 4.3 The Test Menu 83
- 4.3.2 Ribbon Test Label 84
- 4.3.3 Test Label 84
- 4.3.4 Validation Label 84
- 4.3.5 Print Configuration 85
- 4.3.6 Print Last Label 85
- 4.3.7 User-Defined Label 85
- 76 H-Class 86
- Operating, Adjusting and 87
- Maintaining the Printer 87
- If changes require a 89
- 5.2.1 Standard Calibration 90
- Do not position the 93
- Sample Calibration Table 94
- • Die-cut – Remove a label 95
- • Notched – Position the 95
- The re-sampled 97
- 5.3 Reset Methods 99
- 5.3.2 Level One Reset 100
- 5.3.3 Level Two Reset 100
- 5.5 Maintenance 102
- 5.6 Updating the Firmware 110
- 5.8 Fonts 112
- Troubleshooting 117
- To continue printing, enter 125
- 6.2 Hex Dump Mode 127
- Specifications 129
- H-6212X & H-6310X Models 136
- Media (continued) 140
- 132 H-Class 142
- Appendix A 143
- File Handling Messages 144
- 136 H-Class 146
- Appendix B 147
- Speed Ranges 148
- 140 H-Class 150
- Appendix C 151
- Serial Port 152
- Pin Number 152
- RS-422 & RS-485 152
- Function 152
- Appendix D 153
- Appendix E 157
- 148 H-Class 158
- Appendix F 159
- Assigned IP Address 160
- Using the HTML Pages 161
- 152 H-Class 162
- Appendix G 163
- Glossary 177
Prodotti e manuali riguardandi Stampanti per etichette Datamax O'Neil H-4310X
(100 pagine)Greenway Home Products GWD6960BLS Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Greenway Home Products GWD6960BLS.
Wir stellen 1 PDF-Handbücher Greenway Home Products GWD6960BLS zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commenti su questo manuale