Datamax-oneil DPL Programmer’s Manual Manuale Utente Pagina 175
- Pagina / 296
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Appendix C – Available Fonts
167
Font Height Width Spacing Point Size
Font 0 20 14 2 2.4
Font 1 38 20 6 4.6
Font 2 54 30 6 6.5
Font 3 80 42 6 9.6
Font 4 106 54 8 12.7
Font 5 154 54 8 18.5
Font 6 190 94 12 22.8
Font 7 94 44 14 11.3
Font 8 82 44 14 9.8
Internal Smooth Font 9 (Smooth Font) Point Size Specifiers
Label format records with font code 9 (in Format Record header field b) can specify any of
the font sizes in the leftmost column of the table below. The corresponding specification in
either column labeled Ann or 0nn is used in the font size/selection (eee height) field to
select the desired font size. Optional font sets may contain subsets of those described here.
For an optional font set that generates these fonts via scalable font technology, the
character mapping for this font is the selected scalable symbol set (see Appendix E).
In the sample format below, a 300 DPI printer will use 4-point smooth font to produce a
printed label with the words “four point font”. Sample format:
<STX>L<CR>
1911A0400100010four point font<CR>
E<CR>
Point Size
Smooth Font 9 Font Size Specification Syntax
Ann
0nn
203 DPI 300, 400, & 600 DPI
4 - A04
-
5 - A05
000
[1]
6 A06 A06 001
8 A08 A08 002
10 A10 A10 003
12 A12 A12 004
14 A14 A14 005
18 A18 A18 006
24 A24 A24 007
30 A30 A30
008
36 A36 A36
009
48 A48
A48
010
72 - A72
-
[1]
Available at 300 DPI and greater print resolutions only.
- Programmer’s Manual 1
- Contents 3
- 1 Overview 9
- General Conventions 10
- Special Instructions 10
- Typical Data Flow Sequence 11
- ) commands can be changed at 13
- Overview 14
- 15
- Alternate Control Code Modes 16
- Immediate Command Functions 17
- SOH B Toggle Pause 19
- SOH C Stop/Cancel 20
- SOH D SOH Shutdown 20
- SOH F Send Status Byte 21
- STX A Set Time and Date 23
- STX I Input Image Data 27
- STX o Cycle Cutter 30
- STX P Set Hex Dump Mode 31
- STX p Controlled Pause 31
- STX Q Clear All Modules 31
- STX q Clear Module 32
- STX R Ribbon Saver Control 32
- STX S Set Feed Speed 33
- STX T Print Quality Label 33
- STX X Set Default Module 37
- STX z Pack Module 40
- Extended System-Level 41
- STX Kb Backfeed Time Delay 44
- STX KC Get Configuration 45
- STX Kc Configuration Set 48
- STX KE Character Encoding 101
- STX KH Dot Check 104
- STX KI GPIO Input 106
- STX Kn NIC Reset 106
- STX KO GPIO Output 107
- STX Kp Module Protection 108
- Label Formatting 119
- Command Functions 119
- A Set Format Attribute 120
- B Bar Code Magnification 121
- C Set Column Offset Amount 121
- H Enter Heat Setting 124
- J Justification 125
- M Select Mirror Mode 125
- P Set Print Speed 126
- of .37 128
- S Set Feed Speed 130
- Embedding 135
- STX D Print adjusted date 137
- STX T Print Time and Date 138
- Introduction 141
- )s###W Font Descriptor 142
- *c###E Character Code 142
- 8 Generating Label Formats 143
- Generating Records 144
- The Structure of a Record 144
- Record Structure Types 148
- Fill Patterns 155
- Generating Label Formats 158
- Appendix A 161
- 10K OHM 1/4 WATT 163
- Appendix B – Sample Programs 164
- Appendix C 173
- Appendix C – Available Fonts 176
- Appendix D 179
- Appendix D – Reset Codes 180
- Appendix E 181
- Appendix E – Symbol Sets 192
- Appendix F 193
- Appendix G 199
- Barcode I 204
- Barcode S 208
- Barcode T 208
- Barcode U 211
- Barcode z 212
- Barcode Z 213
- Barcode W1c 215
- Barcode W1C 216
- Barcode W1D 220
- Barcode W1f 225
- Barcode W1F 225
- Barcode W1G 226
- Barcode W1I 228
- Barcode W1J 229
- Barcode W1k 231
- Barcode W1L 233
- Barcode W1M 235
- Barcode W1m 235
- Barcode W1N 235
- (IMB) 236
- 34 567890 123 4567 238
- Barcode W1t 239
- Barcode W1Y 240
- Barcode W1Z 242
- Appendix H 245
- Appendix I 247
- Appendix J 251
- • Pins 1 – 2 = +5VDC; 252
- • Pins 2 – 3 = +24VDC; or 252
- • None = A common external 252
- Appendix K 253
- Appendix L 255
- Appendix M 257
- Appendix N 259
- Appendix N – Image Loading 260
- Appendix O 261
- Appendix P 263
- Appendix Q 273
- Appendix R 275
- Appendix R – Line Mode 276
- Appendix S 279
- Appendix S – RFID Overview 280
- Field Valid Inputs Meaning 283
- Appendix T 285
- Appendix U 291
- Glossary 293
Prodotti e manuali riguardandi Stampanti per fotografie Datamax-oneil DPL Programmer’s Manual
(8 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale